Product SKUs |
|
SYS-6026TT-IBQF |
SuperServer 6026TT-IBQF (Black) |
Motherboard |
|
Processor/Cache |
|
CPU |
Dual 1366-pin LGA Sockets |
Supports up to two Intel® 64-bit Xeon® processor(s) of the same type below: |
|
Quad-Core Intel® Xeon®Processor 5500 sequence (Nehalem-EP processor) |
|
QPI |
up to 6.4 GT/s |
System Memory (per Node) |
|
Memory Capacity |
Twelve 240-pin DIMM sockets |
Supports up to 48 GB 1333 / 1066 / 800MHz DDR3 ECC Registered memory |
|
Memory Mirroring supported |
|
Memory Type |
1333 / 1066 / 800MHz Registered ECC DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs |
DIMM Sizes |
1GB, 2GB, 4GB |
Memory Voltage |
1.5 V |
Error Detection |
Corrects single-bit errors |
Detects double-bit errors (using ECC memory) |
|
Supports Intel® x4 and x8 Single Device Data Correction (SDDC) |
|
On-Board Devices (per Node) |
|
Infiniband |
Mellanox ConnectX QDR Infiniband 40Gbps Controller |
Chipset |
Intel® 5520 (Tylersburg) chipset |
ICH10R + IOH-36D |
|
SATA |
Intel ICH10R SATA 3.0Gbps Controller |
RAID 0, 1, 5, 10 support |
|
IPMI |
Support for Intelligent Platform Management Interface v.2.0 |
IPMI 2.0 with virtual media over LAN and KVM-over-LAN support |
|
Winbond® WPCM450 BMC |
|
Network Controllers |
Intel® 82576 Dual-Port Gigabit Ethernet Controller |
Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output |
|
Intel® I/OAT 3 support for fast, scaleable, and reliable networking |
|
VMDq support for better performance of virtualization |
|
1x Realtek RTL8201N PHY (dedicated IPMI) |
|
Graphics |
Matrox G200eW 8 MB DDR2 |
Super I/O |
Winbond W83527HG chip |
Clock Generator |
932S421 chip |
Input / Output (per Node) |
|
Serial ATA |
Six Serial ATA ports |
3 SATA hard drives supported |
|
LAN |
2x RJ45 LAN ports |
1x RJ45 Dedicated IPMI LAN port |
|
USB |
2 rear + 1 header (2 Ports) |
4 total USB ports, 2.0 Compliant / 1.1 Compliant |
|
VGA |
1x VGA Port |
Serial Port |
1 Fast UART 16550 serial port |
Infiniband |
1 External QSFP Infiniband Connector |
System BIOS (per Node) |
|
BIOS Type |
32Mb SPI Flash EEPROM with AMI® BIOS |
BIOS Features |
Plug and Play (PnP) |
PCI 2.2 |
|
ACPI up to 3.0 |
|
USB Keyboard support |
|
Chassis |
|
Form Factor |
2U Rackmount |
Model |
SC827TQ-1200B |
Dimensions |
|
Height |
3.5" (89mm) |
Width |
17.2" (437mm) |
Depth |
28.5" (724mm) |
Gross Weight |
85 lbs (38.6kg) |
Available Colors |
Black |
Front Panel (per Node) |
|
Buttons |
Power On/Off button |
UID button |
|
LEDs |
Power LED (on power button) |
UID LED (on UID button) |
|
Network activity LED |
|
System Overheat/fan fail/power fail/ LED |
|
Expansion Slots (per Node) |
|
PCI-Express |
1 (x16) PCI-E ( Low Profile) |
Drive Bays (per Node) |
|
Hot-swap |
3x 3.5" SATA Hot-swap drive bays |
Hard drive Backplane |
|
2U Hard drive Backplane |
|
System Cooling |
|
Fans |
4x Cooling Fans |
Power Supply |
|
1200W high-efficiency power supply with PMBus |
|
AC Input |
100 - 140V, 50 - 60Hz, 7.5 - 11Amp |
180 - 240V, 50 - 60Hz, 5 - 8Amp |
|
DC Output |
4 Amp |
+5V standby |
|
DC Output |
74 Amp @ 100-140V |
+12V |
100 Amp @ 180-240V |
PC Health Monitoring |
|
CPU |
Monitors for CPU Cores,+1.5V, +3.3V, +5V, +12V, +5 Stdby, +3.3 Stdby, VBAT, Memory Voltages. |
CPU Core 6-Phase-switching voltage regulator |
|
FAN |
Total of four 4-pin PWM fans |
4x fans with tachometer monitoring |
|
Status monitor for speed control |
|
Status monitor for on/off control |
|
Low noise fan speed control |
|
Temperature |
Monitoring for CPU and chassis environment |
CPU thermal trip support |
|
Thermal Control for 4x Fan Connectors |
|
PSU I2C temperature sensing logic |
|
Thermal Monitor 2 (TM2) support |
|
PECI |
|
LED |
Power Fail / Overheat LED |
Suspend-state Indicator LED |
|
UID LED |
|
Other Features |
SDDC Support |
Operating Environment / Compliance |
|
RoHS |
RoHS Compliant |
Environmental Spec. |
Operating Temperature: 10°to 35°C (50°to 95°F) |
Non-operating Temperature: -40°to 70°C (-40°to 158°F) |
|
Operating Relative Humidity: 8% to 90% (non-condensing) |
|
Non-operating Relative Humidity: 5 to 95% (non-condensing) |