Siêu Thị Máy Chủ » Supermicro system » Twin Solutions Supermicro 6026TT-D6IBXRF (Code Name: 6026TT-D6IBXRF)

Two systems (nodes) in a 2U form factor. Each node supports : Intel® Xeon® processor 5600/5500 series, with QPI up to 6.4 GT/s Up to 192GB DDR3 1333/1066MHz ECC Registered DIMM /48GB Unbuffered DIMM 2 (x8) PCI-E (FH/HL) w/ riser card (in x16 slots) Integrated IPMI 2.0 with KVM and Dedicated LAN Dual Intel® 82574L Gigabit Ethernet Controller 6x Hot-swap 3.5" SAS Drive Bays 1400W Gold-level High-efficiency Redundant Power Supply Mellanox ConnectX DDR Infiniband 20Gbps Controller w/ QSFP connector

chỉ còn 0 VNĐ

Chi tiết

Product SKUs SYS-6026TT-D6IBXRF SuperServer 6026TT-D6IBXRF (Black)   Motherboard 2x Super X8DTT-HIBXF+   Processor/Cache CPU Dual 1366-pin LGA Sockets Supports up to two Intel® 64-bit Xeon® processor(s) of the same type below:   Intel® Xeon® Processor X5600/E5600/L5600 Series (Westmere) 40W - 130W   Intel® Xeon® Processor X5500/E5500/L5500 Series (Nehalem-EP) 38W - 95W   QPI up to 6.4 GT/s   System Memory Memory Capacity 12x 240-pin DIMM sockets Supports up to 192 GB** 1333 / 1066 / 800MHz DDR3 ECC Registered memory Supports up to 48 GB 1333 / 1066 / 800MHz DDR3 ECC / Non ECC Unbuffered memory Memory Mirroring supported Memory Type 1333 / 1066 / 800MHz ECC Registered / ECC or Non ECC Unbuffered DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs DIMM Sizes 1GB, 2GB, 4GB , 8GB** , 16GB** Memory Voltage 1.5 V Error Detection Corrects single-bit errors Detects double-bit errors (using ECC memory) Supports Intel® x4 and x8 Single Device Data Correction (SDDC)   On-Board Devices (per Node) Infiniband Mellanox ConnectX DDR Infiniband 20Gbps Controller Chipset Intel® 5520 (Tylersburg) chipset ICH10R SATA Intel ICH10R SATA 3.0Gbps Controller RAID 0, 1, 5, 10 support IPMI Support for Intelligent Platform Management Interface v.2.0 IPMI 2.0 with virtual media over LAN and KVM-over-LAN support Winbond® WPCM450 BMC Network Controllers Dual Intel® 82574L Gigabit Ethernet Controller Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output Intel® I/OAT 3 support for fast, scaleable, and reliable networking VMDq support for better performance of virtualization 1x Realtek RTL8201N PHY (dedicated IPMI) Graphics Matrox G200eW Super I/O Winbond W83527HG chip Clock Generator 932S421 chip   Input / Output (per Node) Serial ATA Six Serial ATA ports 6 SATA hard drives supported LAN 2x RJ45 LAN ports 1x RJ45 Dedicated IPMI LAN port USB 2 rear + 1 header (2 Ports) 4 total USB ports, 2.0 Compliant / 1.1 Compliant VGA 1x VGA Port Serial Port 1 Fast UART 16550 serial port Infiniband 1 External QSFP Infiniband Connector   System BIOS (per Node) BIOS Type 32Mb SPI Flash EEPROM with AMI® BIOS BIOS Features Plug and Play (PnP) PCI 2.2 ACPI up to 3.0 USB Keyboard support Chassis Form Factor 2U Rackmount Model CSE-827HD-R1400B   Dimensions Height 3.5" (89mm) Width 17.2" (437mm) Depth 28.5" (724mm) Gross Weight 85 lbs (38.6kg) Available Colors Black   Front Panel (per Node) Buttons Power On/Off button UID button LEDs Power LED (on power button) Network activity LED System Overheat/fan fail/power fail/ LED UID LED (on UID button)   Expansion Slots (per Node) PCI-Express 1 (x16) PCI-E 2.0 via riser card  (low-profile)   Drive Bays (per Node) Hot-swap 6x 3.5" hot-swap SAS drive bays   Hard drive Backplane 2U Hard drive Backplane   System Cooling Fans 4x Cooling Fans   Power Supply Redundant 1400W high-efficiency power supply with PMBus AC Input 1200W: 100 - 140V, 50 - 60Hz, 10.5 - 14.7 Amp 1400W: 180 - 240V, 50 - 60Hz, 7.2 - 9.5 Amp DC Output +5V standby 6 Amp DC Output +12V 100 Amp @ 100-140V 116 Amp @ 180-240V Certification   80 PLUS Gold Certified   [ Test Report ]   PC Health Monitoring CPU Monitors for CPU Cores,+1.5V, +3.3V, +5V, +12V, +5 Stdby, +3.3 Stdby, VBAT, Memory Voltages. CPU Core 6-Phase-switching voltage regulator FAN Total of four 4-pin PWM fans 4x fans with tachometer monitoring Status monitor for speed control Status monitor for on/off control Low noise fan speed control Temperature Monitoring for CPU and chassis environment CPU thermal trip support Thermal Control for 4x Fan Connectors PSU I2C temperature sensing logic Thermal Monitor 2 (TM2) support PECI LED Power Fail / Overheat LED Suspend-state Indicator LED UID LED Other Features SDDC Support   Operating Environment / Compliance RoHS RoHS Compliant Environmental Spec. Operating Temperature: 10°to 35°C (50°to 95°F) Non-operating Temperature: -40°to 70°C (-40°to 158°F) Operating Relative Humidity: 8% to 90% (non-condensing) Non-operating Relative Humidity: 5 to 95% (non-condensing) Parts List - (Items Included)   Part Number Qty Description Motherboard / Chassis MBD-X8DTT-HIBXF+ CSE-827HD-R1400B 2 1 Super X8DTT-HIBXF+ Motherboard 2U Black Chassis Air Shroud MCP-310-82708-0B 2 Mylar air shroud for SC827HD 2U Heat sink version Backplane BPN-SAS-827HD 1 Sup 6x3.5ö SATA hdd; hot swap Backplane BPN-ADP-SAS2-H6IR 2 [NR] BPN-ADP-SAS2-H6iR 6 X SAS2 LSI 2108 CD CDR-X8 1 For X8 series Riser Card RSC-R2UT-2E8R-O-P 2 RSC-R2UT-2E8R-O-P Heatsink / Retention SNK-P0038PS 4 2U+ PASSIVE CPU HS FOR INTEL 2U TWIN SERVERS Power Supply PWS-1K41P-1R 2 1400W 1U GOLD LEVEL PWS W/ PM BUS & WX3\" Fan 1 FAN-0111L4 4 80X38MM 9.5K RPM 4-PIN PWM FAN FOR SC827 Mounting Rails MCP-290-00053-0N 1 Rail set, quick/quick, default for 2,3U 17.2\"W STT Nhà cung cấp Liên hệ Tiền/Mua 1 Công Ty TNHH Siêu Siêu Nhỏ Địa chỉ chính: 254A Nguyễn Đình Chiểu - phường 6 - Quận 3 - Tp.Hồ Chí Minh Địa chỉ 1: 57 Láng Hạ - Thành Công Tower P. 1002, Ba Đình, HN   0 VNĐ Product SKUs SYS-6026TT-D6IBXRF SuperServer 6026TT-D6IBXRF (Black)   Motherboard 2x Super X8DTT-HIBXF+   Processor/Cache CPU Dual 1366-pin LGA Sockets Supports up to two Intel® 64-bit Xeon® processor(s) of the same type below:   Intel® Xeon® Processor X5600/E5600/L5600 Series (Westmere) 40W - 130W   Intel® Xeon® Processor X5500/E5500/L5500 Series (Nehalem-EP) 38W - 95W   QPI up to 6.4 GT/s   System Memory Memory Capacity 12x 240-pin DIMM sockets Supports up to 192 GB** 1333 / 1066 / 800MHz DDR3 ECC Registered memory Supports up to 48 GB 1333 / 1066 / 800MHz DDR3 ECC / Non ECC Unbuffered memory Memory Mirroring supported Memory Type 1333 / 1066 / 800MHz ECC Registered / ECC or Non ECC Unbuffered DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs DIMM Sizes 1GB, 2GB, 4GB , 8GB** , 16GB** Memory Voltage 1.5 V Error Detection Corrects single-bit errors Detects double-bit errors (using ECC memory) Supports Intel® x4 and x8 Single Device Data Correction (SDDC)   On-Board Devices (per Node) Infiniband Mellanox ConnectX DDR Infiniband 20Gbps Controller Chipset Intel® 5520 (Tylersburg) chipset ICH10R SATA Intel ICH10R SATA 3.0Gbps Controller RAID 0, 1, 5, 10 support IPMI Support for Intelligent Platform Management Interface v.2.0 IPMI 2.0 with virtual media over LAN and KVM-over-LAN support Winbond® WPCM450 BMC Network Controllers Dual Intel® 82574L Gigabit Ethernet Controller Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output Intel® I/OAT 3 support for fast, scaleable, and reliable networking VMDq support for better performance of virtualization 1x Realtek RTL8201N PHY (dedicated IPMI) Graphics Matrox G200eW Super I/O Winbond W83527HG chip Clock Generator 932S421 chip   Input / Output (per Node) Serial ATA Six Serial ATA ports 6 SATA hard drives supported LAN 2x RJ45 LAN ports 1x RJ45 Dedicated IPMI LAN port USB 2 rear + 1 header (2 Ports) 4 total USB ports, 2.0 Compliant / 1.1 Compliant VGA 1x VGA Port Serial Port 1 Fast UART 16550 serial port Infiniband 1 External QSFP Infiniband Connector   System BIOS (per Node) BIOS Type 32Mb SPI Flash EEPROM with AMI® BIOS BIOS Features Plug and Play (PnP) PCI 2.2 ACPI up to 3.0 USB Keyboard support Chassis Form Factor 2U Rackmount Model CSE-827HD-R1400B   Dimensions Height 3.5" (89mm) Width 17.2" (437mm) Depth 28.5" (724mm) Gross Weight 85 lbs (38.6kg) Available Colors Black   Front Panel (per Node) Buttons Power On/Off button UID button LEDs Power LED (on power button) Network activity LED System Overheat/fan fail/power fail/ LED UID LED (on UID button)   Expansion Slots (per Node) PCI-Express 1 (x16) PCI-E 2.0 via riser card  (low-profile)   Drive Bays (per Node) Hot-swap 6x 3.5" hot-swap SAS drive bays   Hard drive Backplane 2U Hard drive Backplane   System Cooling Fans 4x Cooling Fans   Power Supply Redundant 1400W high-efficiency power supply with PMBus AC Input 1200W: 100 - 140V, 50 - 60Hz, 10.5 - 14.7 Amp 1400W: 180 - 240V, 50 - 60Hz, 7.2 - 9.5 Amp DC Output +5V standby 6 Amp DC Output +12V 100 Amp @ 100-140V 116 Amp @ 180-240V Certification   80 PLUS Gold Certified   [ Test Report ]   PC Health Monitoring CPU Monitors for CPU Cores,+1.5V, +3.3V, +5V, +12V, +5 Stdby, +3.3 Stdby, VBAT, Memory Voltages. CPU Core 6-Phase-switching voltage regulator FAN Total of four 4-pin PWM fans 4x fans with tachometer monitoring Status monitor for speed control Status monitor for on/off control Low noise fan speed control Temperature Monitoring for CPU and chassis environment CPU thermal trip support Thermal Control for 4x Fan Connectors PSU I2C temperature sensing logic Thermal Monitor 2 (TM2) support PECI LED Power Fail / Overheat LED Suspend-state Indicator LED UID LED Other Features SDDC Support   Operating Environment / Compliance RoHS RoHS Compliant Environmental Spec. Operating Temperature: 10°to 35°C (50°to 95°F) Non-operating Temperature: -40°to 70°C (-40°to 158°F) Operating Relative Humidity: 8% to 90% (non-condensing) Non-operating Relative Humidity: 5 to 95% (non-condensing) Parts List - (Items Included)   Part Number Qty Description Motherboard / Chassis MBD-X8DTT-HIBXF+ CSE-827HD-R1400B 2 1 Super X8DTT-HIBXF+ Motherboard 2U Black Chassis Air Shroud MCP-310-82708-0B 2 Mylar air shroud for SC827HD 2U Heat sink version Backplane BPN-SAS-827HD 1 Sup 6x3.5ö SATA hdd; hot swap Backplane BPN-ADP-SAS2-H6IR 2 [NR] BPN-ADP-SAS2-H6iR 6 X SAS2 LSI 2108 CD CDR-X8 1 For X8 series Riser Card RSC-R2UT-2E8R-O-P 2 RSC-R2UT-2E8R-O-P Heatsink / Retention SNK-P0038PS 4 2U+ PASSIVE CPU HS FOR INTEL 2U TWIN SERVERS Power Supply PWS-1K41P-1R 2 1400W 1U GOLD LEVEL PWS W/ PM BUS & WX3\" Fan 1 FAN-0111L4 4 80X38MM 9.5K RPM 4-PIN PWM FAN FOR SC827 Mounting Rails MCP-290-00053-0N 1 Rail set, quick/quick, default for 2,3U 17.2\"W